home *** CD-ROM | disk | FTP | other *** search
/ Gold Medal Software 3 / Gold Medal Software - Volume 3 (Gold Medal) (1994).iso / misc / swradio.arj / README.2ND < prev    next >
Text File  |  1993-12-22  |  3KB  |  52 lines

  1. ▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄
  2.  
  3. A SHORTWAVE RADIO FOR UNDER $5???                     YOU GOTTA BE KIDDING!!!
  4. ▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄
  5.  
  6.  
  7. Yes, you can construct a decent shortwave receiver for a total expenditure of
  8. less than $5.00, with a little luck and a halfway decently stocked "junk box" 
  9. of components.  Here's how it can be done.
  10.  
  11. Refer to the  enclosed files CONVERT.TXT and  AMRADIO.TXT. They describe how
  12. to build a shortwave converter and then install it  into just about any  old
  13. AM table radio or clock radio. Unlike the car radio installation,  you  will
  14. need no external     power supply or speaker,  saving you more than half the
  15. expense of components. The  capacitors needed for  the converter are  common
  16. types, and likely scavengeable from  your own    parts box or available  for
  17. only pennies each   at   a Ham   show. Likewise, the   miscellaneous  parts,
  18. connectors, IC socket, wire, etc. The NE602 IC would  cost you  about $2  at
  19. the same Ham show,  if you can find someone  selling them (they are becoming
  20. more easily available  all  the  time).    A  green IF  transformer for  the
  21. converter could be had for  $0.50  - $1.00,  or maybe  you could (carefully)
  22. salvage one from an old transistor radio PC  board  if you  had  specialized
  23. desoldering equipment and a skilled hand. A 5.1 or 6.2v zener  diode  should
  24. be no problem, costing maybe  another  quarter if  you  needed   to buy one.
  25. Frequency crystals can be purchased for as little as $.25 - $.50 each,  with
  26. some judicious shopping, and   you need only one to start.  If  you must buy
  27. EVERY component for  the converter at   a Ham show, you  might still squeeze
  28. under the $5 limit.  Maybe.
  29.  
  30. If you can't make it  to a  Ham show, or can't find all you need there, well
  31. then, order it by mail from DC Electronics or some other good  supplier (see
  32. READ.ME file), where you will  have  to pay  an extra  $3.50 or so shipping/
  33. handling charge, bringing  your total cost within spittin' distance of  $10.
  34. Sorry about that. That would  mean having to save an extra week's  allowance
  35. before you could enjoy shortwave.
  36.  
  37. I recently converted a dusty old GE AM-only clock radio to  short  wave. The
  38. conversion consisted of bringing the receiver circuit ground  and +V out  to
  39. a mini-jack mounted on the radio's case,  and of  finding and  running   the
  40. tuning capacitor "tap" point out to   a  banana jack, likewise case mounted.
  41. The SW converter  sits atop  the radio  and plugs  into the jacks. I  had to
  42. mount a polarized   plug onto  the power cord in  order to keep the AC "hot"
  43. line away from the  chassis.  [See the enclosed  file  AMRADIO.TXT for  more
  44. details.]   The entire procedure took a little over an hour.  The total cost
  45. to me was $0.50 for the    polarized power  plug,  since  I happened to have
  46. everything else on   hand  from previous  projects.  The converted  radio is
  47. almost as good a  short wave receiver in  most respects as the converted car
  48. radios I have worked on.  Keep in mind that car radios are usually built  to
  49. a higher quality  standard  than table radios, with smoother   tuning,  less
  50. sensitivity to noise interference, etc.
  51.  
  52.